AGILE ALLY PLUS 6287 Bedienungsanleitung PDF herunterladen (Seite 143)

Page 11-176287 ULTRA COMPATIBILITY

B — Reserved (not used)

Table B is reserved in the current ULTRA firmware version, and it has no

ALLY PLUS equivalent.

C — Reserved (not used)

Table C is reserved in the current ULTRA firmware version, and it has no

ALLY PLUS equivalent.

1 2 ... 138 139 140 141 142 143 144 145 146 147 148 ... 185 186

6287 ALLY PLUS 1
Copyright Information 2
Release Notes 2
About AGILE 3
Also From AGILE 4
TABLE OF CONTENTS 5
PROGRAMMABLE FUNCTION STRINGS 8
TRANSLATE TABLES 10
COAX HOST CONSIDERATIONS 10
XEROX APPLICATIONS 11
SCS DATA STREAMS 11
DSC DATA STREAMS 11
ALTERNATE HOST CONSIDERATIONS 12
6287 ULTRA COMPATIBILITY 12
APPENDIX 14
GLOSSARY 14
About This Manual 15
AGILE Product Warranty 16
Page xviiPREFACE 17
FCC Statement 18
Warnings 19
Electrical Shock 19
Standard Factory Setup 19
Serial Port Setup 19
Coax Host Considerations 20
Power-On Reset 20
INTRODUCTION 21
INSTALLATION 25
Unpacking 26
Connections 27
Dual Printer Installation 29
6287 ALLY PLUS Front Panel 31
Extended Modes 33
Resetting to Defaults 34
6287 ALLY PLUS Power Up 34
Connection Tests 35
Coax Host Verification 36
Alternate Host Verification 37
Software Upgrades 39
CONFIGURATION 41
Configuration Defaults 43
Configuration Groups 45
Printer Output (Group #00) 45
01 — Output type 46
02 — Character set 46
03 — Plotter support 47
05 — Plotter support 47
11 — SCS left margin 48
12 — SCS right margin 48
13 — SCS top margin 49
14 — SCS bottom margin 49
15 — SCS line spacing 50
21 — DSC left margin 51
22 — DSC right margin 51
23 — DSC top margin 52
24 — DSC bottom margin 52
25 — DSC line spacing 53
30 — FF before Local Copy 55
31 — FF after Local Copy 55
Serial Port Setup (Group #40) 56
44 (4A) — Stop bits 57
Host Parameters (Group #50) 58
53 — Coax port timer 59
54 — LU1 bracketing 59
SCS TH and RH -> 60
2C 00 06 01 00 0C 00 90 80 60
62 — Pseudo transparency 62
63 — DSC PTM trigger 1 64
64 — DSC PTM trigger 2 64
65 — SCS PTM trigger 1 64
66 — SCS PTM trigger 2 65
70 — DisplayWrite 370 support 67
71 — MD-Laser support 69
72 — Metacode support 69
75 — Continuous bell ringing 71
76 — Eliminate C0 05 header 71
77 — CR with each FF 71
78 — Laserpage support 72
79 — Continuous program mode 72
80 — Parallel port 1 timer 73
81 — Parallel port 2 timer 73
82 — Serial port 1 timer 73
83 — Serial port 2 timer 74
PROGRAMMABLE FUNCTION 75
Programming PFSs 76
PFS Descriptions 78
%61 — sc1 Replacement 84
%62 — sc2 Replacement 84
%63 — sc3 Replacement 84
Job Boundary PFSs 85
Job Boundary PFS Examples 86
Print Job chart 91
LU1 Session 91
LU3 Session 92
Translate Table Selection 94
Functions 95
Function Options 96
Reading Translate Tables 97
Modifying Translate Tables 98
The Translate Tables 99
Page 5-9TRANSLATE TABLES 101
Page 5-11TRANSLATE TABLES 103
Page 5-13TRANSLATE TABLES 105
Page 5-15TRANSLATE TABLES 107
Requirements 110
APL Support 110
Transparent (TRN) — 35h 117
Vertical Tab (VT) — 0Bh 117
SCS Command Summary 118
Request Errors = 10h 119
Request Reject = 08h 119
XPAF Support 124
Metacode Support 125
Dip Switch Emulation 128
Configuration Options 129
PFS Downloading 138
Accessing PFSs from the Host 141
Translate Table Downloading 141
B — Reserved (not used) 143
C — Reserved (not used) 143
Page 12-3APPENDIX 147
Page 12-7APPENDIX 151
Page 12-9APPENDIX 153
Page 12-11APPENDIX 155
Page 12-13APPENDIX 157
Page 12-15APPENDIX 159
Printer Test Report 161
Plotter Test Report 162
Host Diagnostic Report 163
Page 12-21APPENDIX 165
Page 12-23APPENDIX 167
Page 12-25APPENDIX 169
Pin-out Charts 172

Kommentare zu diesen Handbüchern

Keine Kommentare

AGILE ALLY PLUS 6287 Bedienungsanleitung Seite 143

Kommentare zu diesen Handbüchern